Study Hall
Sponsored by
Audio Technica

Basic Mixer And Other Common Audio System Connections

Clearing up confusion and answering key questions in audio device interconnect, along with implementing effects devices and utilizing key mixer functions


By Bruce Bartlett March 4, 2013

Figure 1: Mixer connections.

Sound systems can be confusing because they’re made up of complex devices that need to work together to deliver the desired results.

Some of the questions I’ll answer here include:

  • How do I hook up a mixer to the rest of the system? What jacks are best to use?
  • How do I use graphic equalizers?
  • What are compressors used for?
  • How do I use groups?
  • How do I set up monitor mixes?
  • How do I set up the mixer to add effects?

 

Here we go… And note that all of the topics addressed in this article are illustrated in Figure 1.

1) What jacks should I use to connect the mixer to my sound system?

  • Connect each mic to the stage box (snake).
  • Connect each snake XLR connector to each mic input XLR connector.
  • Connect the mixer master or main output to your graphic equalizer input, and connect the graphic output to your house power-amp input. If you’re not using a graphic equalizer for the house speakers, connect the mixer master outputs to the inputs of the power amp that drives the house speakers.
  • If you are recording a board mix of the service or show, connect the mixer REC OUT or TAPE OUT connectors to the recorder line inputs.

2) Why would I put a graphic equalizer between the mixer and power amps? Isn’t that what the mixer EQ is for?

Mixer EQ affects the sound of each individual instrument and voice, while the graphic EQ affects the sound of the complete mix. The graphic equalizer is used the flatten the frequency response of the house speakers and room so that the entire sound system is accurate or hi-fi.

One way to set a graphic EQ is to play some reference CDs alternately through high-quality headphones and through the house loudspeakers. Adjust the graphic-EQ sliders to make the loudspeakers sound like the headphones in their bass-midrange-treble balance.

Here’s another way to set a graphic equalizer:

  • Obtain a measurement microphone, which is an omnidirectional condenser mic with a flat frequency response. Put the mic in the center of the audience area.
  • Plug the mic into a real-time analyzer (RTA) set to display 1/3-octave bands.
  • Play pink noise through one set of house loudspeakers (one combination of woofer, midrange and tweeter drivers).
  • On the graphic equalizer, pull down the frequencies that are the highest on the RTA display.
  • Try to get a flat spectrum (equal level in each frequency band) up to 1 kHz, then let the spectrum roll off gradually to about 10 dB down at 10 kHz. This is called a “house curve.”

It’s also common to use a graphic EQ between the mixer’s monitor send (aux out) jack and the power amp that drives the monitor speakers. That EQ is used to reduce the levels of frequencies that feed back.

You also can use the graphic EQ to reduce the “bassy” sound in the monitors caused by microphone proximity effect (the bass boost that occurs when directional mics are used up close). The monitor signal from the board is pre-EQ, so turning down the bass (low frequencies) on the mic channel does not turn down the bass in the monitor loudspeakers.

That’s where a graphic EQ can help: turn down frequencies a few dB below 200 Hz or so. Then the monitor loudspeakers won’t sound too bassy and muddy.

3) What’s a compressor for? How do I connect it to a mixer?

A compressor is used to reduce the dynamic range of whatever signal you pass through it. For example, a lead vocalist might suddenly sing a very loud note, blasting the listeners.

The compressor is an automatic volume control – it turns down loud notes so they don’t get too loud. If this isn’t a problem in your venue, you don’t need a compressor.

Insert a compressor in-line with one of the mic channels. Find the mic channel on the back of the mixer, and connect its insert send to the compressor input. Connect the compressor output to the insert return on the same mixer channel.

If there is only one insert jack per channel, the tip of the jack is send and the ring of the jack is return, so use a stereo phone plug at the mixer going into two plugs (in and out) at the compressor.

4) Would I use grouping to combine several channels into one — say, for a monitor for just the vocalists?

The groups are for the house loudspeakers, not the monitor loudspeakers. You might assign all the vocal mics to Group 1 (also called Subgroup 1 or Submix 1).

Then you can control the overall level of the vocals with just the Group 1 fader. Start with the group fader and master fader about 3/4 up (at unity gain, or 0 dB).

Groups don’t have to be used, but some find it convenient to do so. If you don’t use them, just assign each mic channel to the stereo mix bus (the master stereo output of the console), and turn down all the group faders because they are not being used.

To confuse things, some consoles use Group 1 and Group 2 as the main stereo output channels. Other consoles have groups plus a separate stereo master output channel.

5) How do I set up monitor mixes?

The aux knobs on a mixer can serve either for monitor mixes or for controlling the amount of effects on each input channel. First decide which aux channel you want to use for a monitor mix.

The choice might be several aux channels (aux 1, aux 2, aux 3) to create separate monitor mixes for different performers. Each aux number is a separate monitor mix feeding a power amplifier channel that is in turn feeding a separate monitor loudspeaker.

Let’s start with just one monitor mix. Suppose that you’ll create a monitor mix with all the aux 1 knobs.

On the back of the mixer, connect the aux 1 send connector to the graphic equalizer (if any) used for the monitor speakers, and connect the graphic equalizer output to the monitor power amp input. If you’re not using a graphic EQ with the monitor loudspeakers, connect the aux 1 send to the monitor power amp input.

Set all of the monitor aux knobs to pre-fader so that the fader for each channel does not affect the monitor level.

What if you need several different monitor mixes? You might use all the aux 1 knobs to set up a monitor mix for the vocalists. Connect aux 1 out to the power amp channel for the vocalists’ monitor loudspeakers.

Then use all the aux 2 knobs to set up a monitor mix for the drummer. Connect aux 2 out to the power amp channel for the drummer’s monitor loudspeaker. Use aux 3 for the piano player, and so on.

For example, let’s say the vocalists need to hear only the piano and vocals in their monitors. Use all the aux 1 knobs across the console to set up a monitor mix for the vocalists. Turn up the piano channel’s aux 1 knob about halfway.

Also, turn up the vocal channels’ aux 1 knobs about halfway, and turn up the aux 1 master knob (if any) about halfway. Make sure the vocalists can hear the monitor mix, and adjust it according to what they want. Turn up the aux knobs slowly and stay below the feedback point.

Similarly, suppose the drummer needs to hear only the piano and bass. Use all of the aux 2 knobs across the console to set up a monitor mix for the drummer. Turn up the piano channel’s aux 2 knob about halfway.

Turn up the bass channel’s aux 2 knob about halfway, then turn up the aux 2 master knob (if any) about halfway. Make sure the drummer can hear the monitor mix, and adjust it according to what the drummer wants.

6) How do I set up the mixer to add effects?

As previously noted, the aux knobs in a mixer can be used either for monitor mixes or for controlling the amount of effects on each input channel. First, decide which aux channel you want to use for effects.

Suppose aux 4 is your effects channel. On the back of the mixer, connect the aux 4 send connector to the input of the effects device. Connect the output of the effects device to the Bus In or Effects Return connector on the mixer.

Another option is to connect the effects outputs to the line inputs of two extra input channel strips on the mixer, then have those be the effects-return level controls.

Set the effects send (aux 4) knobs to post-fader so that the fader level also controls the amount of effects. Set the dry/wet mix control on the effects unit all the way to wet (100 percent effect).

For each input channel (vocal or instrument), use the aux 4 knob to set the amount of effects you want to hear on that vocal or instrument. Note that some mixers have effects built in so you don’t need to make any effects connections.


About Bruce

Bruce Bartlett
Bruce Bartlett

Recording Engineer
   
AES and SynAudCon member Bruce Bartlett is a recording engineer, audio journalist, and microphone engineer. His latest books are “Practical Recording Techniques 5th Ed.” and “Recording Music On Location.”
http://www.bartlettaudio.com

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *

Russell McCallum says

Thank you Bruce, that clears up a lot of confusion for me. Just using small mixer with a small group, but like to know what I doing- LOL
Thanks again
Russ

Aniekan David says

I'm glad to have gone through such an article

erick says

Hi I would love to know how to connect and control the bass guitar from the mixer.currently the bass guitar runs on the bass combo and at times it gets too loud

wayne gudde says

Hay Bruce.
i have a soundcraft K1 compact mixer (24ch)
got the manual off internet. does not show how to
use it.. can you tell me how to hook up the bd to my pivey 400BH 800watts? the back of the mixer does not show outputs for the mixer or it i want to use pwd spk where do they hook up.. i'm realy lost here..
thanks a bunch..
wayne gudde

jhade t gonzales says

what is the best or good connecting amp to the mixer plzzzzzz help me becuse im the newbies for bieeeng snounth tech

Adams M Deh says

thanks very mush for your lesson is very good and understanding

claude fabrice umuhc says

I would like to ask you how to link crossover graphic equalizer ;anplifiers loud speakers to mixer and we hear a best sound
Thanks

stemex says

How do i send sound from a Tervey Bass Combo to the sound system... I want to know, mine is giving me difficulty

John A. Gulow says

Hello,
I own an '80s Carvin MX1688 16 input channel/8 output channel mixing board. The MX1688 has 2 aux's built in- Effect Send 1&2 and Effect Return A&B. I am trying to figure out how best to use them to spread a '70s Eventide 1745M DDL's 4 outputs between 4 channels on the board. I also want to use an '80s MXR M125, rack mount, 31-band graphic equalizer, instead of the Carvin's on-board 3-band parametric equalizers, to equalize everything before it goes to the power amps, and then out to the PA system. How do I connect both devices into the board to accomplish this? I think I can use the 2 aux's I mentioned above, but I'm not at all certain. I'm very green, so please- use small words! :) Thank you VERY much!

Tagged with:

Subscribe to Live Sound International

Subscribe to Live Sound International magazine. Stay up-to-date, get the latest pro audio news, products and resources each month with Live Sound.

Latest in News