PrepareToTest AMT Airframe Quiz http://preparetotest.com/faa/rss/index.php?exam_key=ama Practice Questions for AMT Airframe Exam Sat, 18 May 2013 0:04:01 GMT en-us PrepareToTest AMT Airframe Quiz http://preparetotest.com/images/faa/misc/rss_logo.gif http://preparetotest.com/faa/rss/index.php?exam_key=ama 100 33 1. Install instruments and perform a static pressure system leak test (8636) Sat, 18 May 2013 0:04:01 GMThttp://preparetotest.com/faa/rss/index.php?exam_key=ama%26q_num%3D1%26num%3D8636Where may a person look for the information necessary to determine the required markings on an engine instrument? 1. Engine manufacturer's specifications. 2. Aircraft flight manual. 3. Instrument manufacturer's specifications. 4. Aircraft maintenance manual.

  • A - 2 or 4.

  • B - 1 or 4.

  • C - 2 or 3.

    • Click the answer you think is correct

    ]]>         2. Solder, braze, gas and arc weld steel (8187) Sat, 18 May 2013 0:04:01 GMThttp://preparetotest.com/faa/rss/index.php?exam_key=ama%26q_num%3D2%26num%3D8187Which statement concerning soldering is correct?

  • A - Joints in electric wire to be soldered should be mechanically secure prior to soldering.

  • B - Changeable shades of blue can be observed on the surface of a copper soldering tip when the proper temperature for soldering has been reached.

  • C - If the soldering temperature is too high, the solder will form in lumps and not produce a positive bond.

    • Click the answer you think is correct

    ]]>         3. Repair hydraulic and pneumatic power system components (8399) Sat, 18 May 2013 0:04:01 GMThttp://preparetotest.com/faa/rss/index.php?exam_key=ama%26q_num%3D3%26num%3D8399What type of selector valve is one of the most commonly used in hydraulic systems to provide for simultaneous flow of fluid into and out of a connected actuating unit?

  • A - Four-port, closed-center valve.

  • B - Three-port, four-way valve.

  • C - Two-port, open-center valve.

    • Click the answer you think is correct

    ]]>         4. Inspect and repair sheet metal structures (8128) Sat, 18 May 2013 0:04:01 GMThttp://preparetotest.com/faa/rss/index.php?exam_key=ama%26q_num%3D4%26num%3D8128(Refer to Figure 2 .) Select the preferred drawing for proper countersinking.

  • A - All are acceptable.

  • B - 2.

  • C - 1.

    • Click the answer you think is correct

    ]]>         5. Install conventional rivets (8147) Sat, 18 May 2013 0:04:01 GMThttp://preparetotest.com/faa/rss/index.php?exam_key=ama%26q_num%3D5%26num%3D8147Mild steel rivets are used for riveting

  • A - nickel-steel parts.

  • B - magnesium parts.

  • C - steel parts.

    • Click the answer you think is correct

    ]]>         6. Weld magnesium and titanium (8181) Sat, 18 May 2013 0:04:01 GMThttp://preparetotest.com/faa/rss/index.php?exam_key=ama%26q_num%3D6%26num%3D8181Which statement is true in regard to welding heat-treated magnesium?

  • A - The welded section does not have the strength of the original metal.

  • B - Flux should not be used because it is very difficult to remove and is likely to cause corrosion.

  • C - Magnesium cannot be repaired by fusion welding because of the high probability of igniting the metal.

    • Click the answer you think is correct

    ]]>         7. Inspect, check, service, troubleshoot and repair heating, cooling, air conditioning, pressurization (8557) Sat, 18 May 2013 0:04:01 GMThttp://preparetotest.com/faa/rss/index.php?exam_key=ama%26q_num%3D7%26num%3D8557When purging a freon air-conditioning system, it is important to release the charge at a slow rate. What is the reason for the slow-rate discharge?

  • A - Prevent the large amount of freon from contaminating the surrounding atmosphere.

  • B - Prevent excessive loss of refrigerant oil.

  • C - Prevent condensation from forming and contaminating the system.

    • Click the answer you think is correct

    ]]>         8. Inspect, check, troubleshoot, service and repair airframe ice and rain control systems (8970) Sat, 18 May 2013 0:04:01 GMThttp://preparetotest.com/faa/rss/index.php?exam_key=ama%26q_num%3D8%26num%3D8970Which of the following are found in a laminated integral electrically heated windshield system?
    1. Autotransformer.
    2. Heat control relay.
    3. Heat control toggle switch.
    4. 24V dc power supply.
    5. Indicating light.

  • A - 1, 2, 4, 5.

  • B - 2, 3, 4, 5.

  • C - 1, 2, 3, 5.

    • Click the answer you think is correct

    ]]>         9. Inspect, check, troubleshoot, service and repair oxygen systems (8580) Sat, 18 May 2013 0:04:01 GMThttp://preparetotest.com/faa/rss/index.php?exam_key=ama%26q_num%3D9%26num%3D8580Before a high-pressure oxygen cylinder is serviced, it must be the correct type and have been

  • A - hydrostatically tested within the proper time interval.

  • B - approved by the National Transportation Safety Board.

  • C - inspected by a certificated airframe mechanic. Before high-pressure oxygen cylinders can be serviced, it must be determined that they are of the correct type and that they have been hydrostatically checked for burst strength within the proper time interval.

    • Click the answer you think is correct

    ]]>         10. Inspect bonded structures (8058) Sat, 18 May 2013 0:04:01 GMThttp://preparetotest.com/faa/rss/index.php?exam_key=ama%26q_num%3D10%26num%3D8058When repairing puncture-type damage of a metal faced laminated honeycomb panel, the edges of the doubler should be tapered to

  • A - two times the thickness of the metal.

  • B - 100 times the thickness of the metal.

  • C - whatever is desired for a neat, clean appearance.

    • Click the answer you think is correct

    ]]>